door tubular motor receiver TM5211
remote control switch/receiver tubular motor receiver
Packaging & Delivery
-
Product size
12 x 7.6 x 4.6 cm
-
Product weight
370 g
-
CTN. Spec
36.5*33.5*16 cm / 42pcs
-
G.W/N.W
17 / 16 kg
-
Certification
CE/RoHS
-
Frequency
433.92MHz
-
Code
rolling code
-
Color
White
-
Working voltage
220VAC,50HZ
-
Product size
113*74*44mm
-
Product weight
340g
-
Transmitters stored
30
-
Suitable tubular motor
35mm, 45mm, 55mm, 59mm, 64mm, 92mm, 115mm
-
Loading capacity
2HP,240VAC
-
Self-learning function
yes
-
Working temperature
-20℃~+60℃
-
Build-in fuse
electrocircuit (0.5A), motor (10A)
-
Running time
100S
-
External switch one button& three button
three buttons control
-
Control
three buttons control
-
Operation
Deadman/Impulse adjustable
-
Connect with
external switch, photocell
-
Installation position
outside type
-
With push buttons
Yes
I. Specification
1 .Working voltage: 220VAC,50HZ
2. Loading capacity: 2HP，240VAC
3. Working frequency: 433.92MHz
4. Built-in fuse: electrocircuit (0.5A), motor (10A)
5. Temperature range: -20℃ to 60℃.
6. Code:Rolling code
7. with external button and photocell protection
8. Size: 113×74×44MM
Ⅱ. Safety Instruction
1.For security, please read the instructions carefully before initial operation; making sure that the power is off before connection.
2 .The received signal may be interfered by other communication devices. (e.g. the wireless control system with the same frequency range)
3. It is forbidden to control the high-risk coefficient equipment / system. (e.g. cranes)
4. It should be applied in dry indoor place or in the electric appliance place.
III. Set up
1. Learning / memorizing transmitters: Press the learning button on the panel,LED turns into red and gets into learning state;press the same button twice on the same transmitter,LED blinks for a while and turns into green shows transmitter has been learned successfully.
2. Erasing Transmitter：Continue pressing the learning button (about 8s) until LED turns green then release the learning button, LED turns red (about 1s) then turns green. It indicates that the erasing process is successful.
IV: Operational process
4.1 Three button control system with transmitter and non-Latch model Button 1,2,3 in transmitter is in correspondence with open, close and stop.
4.2 Three button control with transmitter and latch model Motor works clockwise when keep pressing button 1;Motor works anticlockwise when keep pressing button 2;Motor stops when releasing button
4.3 Single button control system and non-Latch model "Press-Open(motor works clockwise), press-stop, press-close(motor works anti clockwise),press-stop,and so on in a loop. Single-button control is only effective to the learned button; if a new button of transmitter learned into the control panel, the formal one is useless. (e.g.: if learned button ① at first, and then button ② or ③, the former button ① becomes invalid)."
4.4 Single button control and latch model Motor works clockwise/anticlockwise when keep pressing the button; motor stops when releasing.
4.5 Infrared sensor protection It works both when door closing and opening. Motor stops when photocell signal disconnecting during door closing.
(External photocell PHOTO port connects photocell normally close switch,share the same port with external stop button, refers to the connection picture)
NOTE:
1．Single-button control refers to single button in transmitter; ▲ ■ ▼ in control panel is in correspondence with open, close and stop.
2. Max running time means that the motor’s maximum running time at a time is 100S; the motor stops immediately if longer than 100S.
3. ▲ ■ ▼ in control panel and OPEN STOP CLOSE button in transmitter are in correspondence with open,close and stop."
Send your message to us
No need register, just fill in contact info below, we will reply you within 24 hours!
