What Is the Recommended Operating Temperature Range for Hiland Tubular Motors?

For the Hiland TM5202 tubular motor receiver, the documented operating temperature range is -20°C to 60°C. This is the figure to use when checking whether the receiver can cope with cold snaps, hot control enclosures, and typical seasonal temperature swings. The TM5202 is a receiver/control product rather than the tubular motor itself, so its temperature limit should not be applied automatically to every tubular motor model. Always confirm the motor's own label or datasheet for the motor ambient limit.

Why the temperature range matters in real installations

Temperature affects electronic components, relay behavior, soldered joints, and the long-term stability of a gate or door control system. Operating below -20°C or above 60°C takes the TM5202 outside its published range. Even within the range, installers should avoid unnecessary heat build-up and moisture. The manual states that the product should be applied in a dry indoor place or in an electric appliance place, so a protected control enclosure is preferable to an exposed outdoor position.

TM5202 environmental and electrical limits

• Temperature range: -20°C to 60°C
• Working voltage: 220V AC, 50Hz
• Loading capacity: 2HP, 250V
• Working frequency: 433.92MHz
• Built-in fuse: electronic circuit 0.5A and motor 10A; exchange an appropriate fuse according to loading capacity
• Transmitters stored: 30
• Self-learning function included
• Dimensions: 113×74×44 mm

These values define the receiver's documented operating envelope. They do not replace a site-specific risk assessment for condensation, salt air, dust, vibration, or direct water exposure. The supplied product information does not list an IP rating, so the safe practice is to keep the receiver in a dry, protected location.

Cold weather and hot weather guidance

At the cold end, -20°C is the lower published limit. If the installation is expected to fall below that level, the TM5202 should not be relied on as the operating receiver. At the hot end, 60°C is the upper published limit. Control boxes mounted in direct sun, near heat-generating equipment, or in poorly ventilated cabinets can rise above ambient air temperature. Allow ventilation and shade where possible, and verify the actual temperature inside the enclosure during worst-case conditions.

Power failure and supply considerations

The TM5202 works on 220V AC, 50Hz. The available product information does not specify a battery backup or outage ride-through function, so normal operation depends on the mains supply being present and within the stated voltage and frequency. After a power interruption, check the installation before resuming normal use: confirm that safety devices are active, the photocell circuit is correctly connected, and the gate or door area is clear. The manual notes that if no photocell is used, the photocell switch must be connected with short lines; otherwise the door cannot be closed.

Installation and safety limits to respect

• Read the instructions carefully before initial operation.
• Make sure the power is off before connection.
• Clear the memory before initial operation.
• Do not learn a remote control while the motor is operating, to avoid mis-operation.
• Use the receiver in a dry indoor place or in an electric appliance place.
• Replace the fuse with an appropriate rating according to the loading capacity.

FAQ: TM5202 temperature and environment

What is the operating temperature range of the TM5202? The published range is -20°C to 60°C.

Can it be installed outdoors? The manual specifies a dry indoor place or an electric appliance place. Because no IP rating is given in the supplied information, it should not be treated as an exposed outdoor receiver.

Does it work during a power outage? No battery backup or outage operation is stated in the available product information. The receiver depends on its 220V AC, 50Hz supply.

Does the temperature range apply to all Hiland tubular motors? No. The -20°C to 60°C figure applies to the TM5202 receiver as documented here. Check the specific motor datasheet before specifying another model.

Need help matching the receiver to your project?

Hiland supplies transmitter and tubular motor receiver products for wholesale and project requirements. For technical clarification on the TM5202, contact info@hiland.cc or call +86-571-81958376. You can also review the product page at https://www.hiland.cc/auto_gate_system_tubular_motor_receiver_TM5202-html.